Gutter size calculator
Enter the roof area, the pitch, the length of gutter and the rainfall intensity where the house is. The gutter size calculator gives you the K-style gutter size, the downspout count and the math behind it, the same way FollowStack's roof report sizes gutters.
It uses the same SMACNA method as FollowStack's roof report and runs in your browser, so nothing is sent unless you ask us to write to you. Rainfall for 17 US cities is listed below, or you can look up your own from NOAA.
Size the gutters
Want this on every roof you measure?
FollowStack's roof report sizes each gutter run with the job's own NOAA rainfall and counts the end caps, miters and downspouts. Leave your email and we will show you.
Thanks. We will be in touch.
We will write back within one business day to set a time to show you the roof report.
Rainfall intensity for common cities
NOAA Atlas 14, 10-year, 5-minute intensity in inches per hour, read at each city's center on 2026-10-22. The number changes across a metro area, so look up the job's own address when you can.
| City | in/hr |
|---|---|
| San Antonio, TX | 9.16 |
| Austin, TX | 9.58 |
| Houston, TX | 10.1 |
| Corpus Christi, TX | 9.78 |
| Dallas, TX | 8.41 |
| Fort Worth, TX | 8.14 |
| Lubbock, TX | 7.88 |
| El Paso, TX | 6.19 |
| Miami, FL | 10.8 |
| New Orleans, LA | 10.5 |
| Oklahoma City, OK | 8.57 |
| New York, NY | 7.91 |
| Atlanta, GA | 7.76 |
| Chicago, IL | 7.43 |
| Denver, CO | 5.06 |
| Phoenix, AZ | 4.84 |
| Los Angeles, CA | 3.64 |
Where to find your number
- Open NOAA's Precipitation Frequency Data Server.
- Click the job's location on the map, or type its latitude and longitude.
- Set the data type to precipitation intensity and the units to English.
- Read the 5-min row under the 10-year column. That is your number in inches per hour.
How the calculator works
Adjusted area = roof area seen from above × pitch factor × rainfall intensity. Downspouts start at one per 40 ft of gutter, at least one, and go up while a section is still over what a 6 inch gutter carries. A section up to 5,520 adjusted sq ft takes a 5 inch K-style gutter with 2x3 downspouts, and a section up to 7,960 takes a 6 inch with 3x4.
| Roof pitch | SMACNA pitch factor |
|---|---|
| Flat to 3/12 | 1.0 |
| 4/12 and 5/12 | 1.05 |
| 6/12 to 8/12 | 1.1 |
| 9/12 to 11/12 | 1.2 |
| 12/12 and steeper | 1.3 |
It assumes the roof drains evenly along the gutter. If one side of the roof is much bigger than the other, size that run on its own. This is a sizing guide, not an engineered design, so check your local code.
Measuring the roof first? See the roof measurement app, gutter estimating software and Roof mode and takeoffs.
Questions
How do I know if I need 5 inch or 6 inch gutters?
Multiply the roof area that drains to the gutter, measured flat from above, by the pitch factor and by your rainfall intensity. Divide by the number of downspouts. If each section between downspouts drains 5,520 adjusted sq ft or less, a 5 inch K-style gutter is enough. Up to 7,960, use 6 inch. Above that, add downspouts.
What rainfall intensity should I use?
The 10-year, 5-minute intensity in inches per hour from NOAA Atlas 14 for the address. Open NOAA's Precipitation Frequency Data Server, click the spot on the map, choose precipitation intensity in English units, and read the 5-min row in the 10-year column.
Why does roof pitch matter?
A steep roof catches more wind-driven rain than its flat footprint shows, so the SMACNA method raises the area: 1.0 up to 3/12, 1.05 for 4/12 and 5/12, 1.1 for 6/12 to 8/12, 1.2 for 9/12 to 11/12 and 1.3 for 12/12 and steeper.
How many downspouts do I need?
Start with one downspout for every 40 ft of gutter, and at least one per run. If a section still drains more than a 6 inch gutter can carry, add downspouts until it does. 5 inch gutters take 2x3 downspouts and 6 inch gutters take 3x4.
Should I use the roof area or the footprint?
The area seen from above, including the overhangs, that drains to that gutter. Do not use the sloped area from a roof report, because the pitch factor already accounts for the slope.
Measure the roof and size the gutters in FollowStack
Roof mode traces the roof, sets the pitch and sizes every gutter run with the rainfall at that address.